Wire Mesh Machinery
Fully automatic Chain link wire mesh machinery
Date: 2024-09-03 Views: 162
|
|
|
|
|
|
|
|
Introduction
ContentThe fully automatic flower hooking net machine, also known as the movable net machine or diamond net machine, can automatically complete the processes of wire drawing, threading, cutting, bending or twisting, shrinking or rolling in one go. This machine has a fast production speed, saves raw materials, reduces labor, and greatly improves the quality of the mesh. This machine has its own advantages among similar products. This machine has obtained the patent certificate issued by the China National Intellectual Property Administration of the People's Republic of China. Counterfeiting must be investigated.
Mechanical parameters
Name: Fully automatic flower hooking net machine
Model: QZD-400
Overall size: 6.7m x 3.65m x 1.4m
Floor area: 6 x 9 square meters
Weaving width: 4m
Overall weight: 3t
Voltage: 380v
Motor power: 7kV
Silk warp range: 2.0mm-5.0mm
Mesh range: 3cm-8cm
Production capacity: 60-80 ㎡/h
Color: Blue yellow (customizable)
Operating Procedures for Fully Automatic Flower Hooking Machine
1. Before weaving the net, it is necessary to strictly inspect the tools used. The loom should be placed in a clean, dry, and well ventilated place, and the lubrication level of the loom should be checked regularly.
2. Weaving personnel should wear work clothes.
3. Electric welding machines that have not been used for a long time must be checked for good insulation using a shaking table. Whether the wiring part is corroded and damp. Check if the wiring is correct, tight, and secure.
4. When the loom power is turned on, it should be installed in a tight controller. When starting the power, keep your fingers dry and free of oil stains.
5. Fix the metal wire on the rotating shaft and maintain good lubrication of the rotating shaft.
6. Fix one end of the metal wire on the hook shaft.
7. Turn on water lubrication and hydraulic equipment to ensure the normal operation of the wire hook.
8. Turn on the power of the loom to ensure its normal operation.
9. After the crochet net is woven to a certain length, roll one end onto the winding machine, and the loom will operate normally.
Mechanical parameters
Name: Fully automatic flower hooking net machine
Model: QZD-400
Overall size: 6.7m x 3.65m x 1.4m
Floor area: 6 x 9 square meters
Weaving width: 4m
Overall weight: 3t
Voltage: 380v
Motor power: 7kV
Silk warp range: 2.0mm-5.0mm
Mesh range: 3cm-8cm
Production capacity: 60-80 ㎡/h
Color: Blue yellow (customizable)
Operating Procedures for Fully Automatic Flower Hooking Machine
1. Before weaving the net, it is necessary to strictly inspect the tools used. The loom should be placed in a clean, dry, and well ventilated place, and the lubrication level of the loom should be checked regularly.
2. Weaving personnel should wear work clothes.
3. Electric welding machines that have not been used for a long time must be checked for good insulation using a shaking table. Whether the wiring part is corroded and damp. Check if the wiring is correct, tight, and secure.
4. When the loom power is turned on, it should be installed in a tight controller. When starting the power, keep your fingers dry and free of oil stains.
5. Fix the metal wire on the rotating shaft and maintain good lubrication of the rotating shaft.
6. Fix one end of the metal wire on the hook shaft.
7. Turn on water lubrication and hydraulic equipment to ensure the normal operation of the wire hook.
8. Turn on the power of the loom to ensure its normal operation.
9. After the crochet net is woven to a certain length, roll one end onto the winding machine, and the loom will operate normally.
Previous ：Straightening and cutting machine
